Microscope Field of View Calculator
Result
- Field diameter
- Field area
- Total magnification
- across the field
Field diameter for every objective at this field number
- 4× objective5.50 mm
- 10× objective2.20 mm
- 20× objective1.10 mm
- 40× objective0.55 mm
- 60× objective0.37 mm
- 100× objective0.22 mm
Diameter 22 ÷ 40 = 0.55 mm; area π × 0.28² = 0.24 mm²; total 40 × 10 = 400×.
Enter a number.
Calculate microscope field of view from the field number and objective magnification. Get the field diameter in millimetres and microns, plus the field area.
What is microscope field of view?
Microscope field of view is the diameter of the circle you see on the specimen, in millimetres — not an angle. With a field number of 22 and a 40× objective, the field is 22 / 40 = 0.55 mm across, or 550 microns. Everything in that 0.55 mm circle is visible at once; everything outside it is not in the picture.
This is a different kind of field from a camera's. A camera field is an angle in degrees, because the subject can stand at any distance. A microscope subject sits at a fixed distance under the lens, so the field is a length on the slide — a diameter you can measure with a ruler.
- Field diameter
- Field diameter in microns
Field number 22: 4× → 5.5 mm, 10× → 2.2 mm, 40× → 0.55 mm, 100× → 0.22 mm.
The field number — where to find it
The field number is printed on the eyepiece, after the slash: a 10×/22 eyepiece has field number 22. It is the diameter, in millimetres, of the image the eyepiece can pass — the size of the intermediate image at the eyepiece field stop. A bigger field number means a wider view through the same objective.
Common field numbers are 18, 20, 22, 25, and 26. A 22 mm field number is the standard widefield eyepiece; 18 mm is the older narrow eyepiece; 26 mm is a super-widefield eyepiece. If the eyepiece prints no number, the field number is usually 18 mm on an old microscope and 20 mm on a basic student model.
Eyepiece
- Field diameter at 40×
- Field diameter in microns
At 40×: field number 18 → 0.45 mm, 20 → 0.50 mm, 22 → 0.55 mm, 26 → 0.65 mm.
One field number, six objectives
Doubling the objective halves the field, so one table covers every lens on the nosepiece. With field number 22: the 4× scanning objective shows 5.5 mm, the 10× shows 2.2 mm, the 20× shows 1.1 mm, the 40× shows 0.55 mm, the 60× shows 0.37 mm, and the 100× oil objective shows 0.22 mm. Each doubling throws away half the width you could see.
The table is the fastest way to plan a slide. Scan at 4× to find the specimen in a 5.5 mm field, centre it, then step up: at 10× it still fills less than half the field, at 40× it fills the view. A specimen that fits at 10× may not fit at 40× — check the table before switching.
Field number
- 4× objective
- 10× objective
- 20× objective
- 40× objective
- 60× objective
- 100× objective
Field number 22: 5.50, 2.20, 1.10, 0.55, 0.37, 0.22 mm from 4× to 100×.
Total magnification is not the field
The eyepiece changes the total magnification, but it does not change the field diameter. A 40× objective with a 10× eyepiece gives 400× total and a 0.55 mm field. Swap in a 15× eyepiece and the total becomes 600× — but the field is still 0.55 mm, because the field comes from the field number and the objective only.
This is the point beginners get backwards. A stronger eyepiece makes the same 0.55 mm circle look bigger; it does not show more of the slide. To see more, you need a bigger field number or a weaker objective — never a stronger eyepiece.
Eyepiece
- Total magnification
- Field diameter (unchanged)
Total magnification climbs 400× → 600× → 800× while the field stays exactly 0.55 mm.
Field area — why the high-power view feels tiny
Field area shrinks with the square of the diameter, so each step up costs far more area than width. With field number 22, the 4× objective covers 23.76 mm², the 10× covers 3.80 mm², the 20× covers 0.95 mm², and the 40× covers only 0.24 mm². The 40× view shows about one hundredth of the area the 4× view shows.
Area is what matters when you count cells or scan a smear. A 40× field of 0.24 mm² holds about 73 red blood cells across its width, but the area holds thousands — counting a whole slide at 40× means hundreds of fields, while 10× covers the same slide in a few dozen.
Objective
- Field diameter
- Field area
- Share of the 4× area
Field number 22: 4× covers 23.758 mm², 40× only 0.238 mm² — about 1% of the area.
What fits in the field?
Divide the field diameter by the specimen size and you know at a glance what fits. In a 0.55 mm field (field number 22, 40×): a red blood cell at 7.5 microns fits about 73 times across; a human hair at 70 microns fits about 8 times; a cheek cell at 60 microns fits about 9 times; a paramecium at 200 microns fits 2 or 3 times; an amoeba at 500 microns fills almost the whole field on its own.
The same specimen at 10× sits in a 2.2 mm field, so the paramecium that filled a third of the 40× view is a small speck at 10×. Pick the objective that makes the specimen fill a third to a half of the field — big enough to see detail, small enough to see context.
Specimen
- Count across the field
- Fraction of the field one fills
In the 0.55 mm (550 µm) field at field number 22, 40×: a red blood cell fits 73.3 times across; an amoeba fills 0.91 of the field on its own.
Measuring a specimen with the field
The field diameter is a ruler: a specimen that spans half the field is half the field diameter wide. A cell that spans half of a 0.55 mm field is about 275 microns across. For a finer reading, use a calibrated eyepiece reticle: a stage micrometer is 1 mm divided into 100 parts, so each division is 10 microns, and a reticle with 100 divisions across a 0.55 mm field reads 5.5 microns per division.
Calibrate once per objective, because the reticle value changes with the objective. At 10× the same 100-division reticle reads 22 microns per division (2.2 mm / 100); at 100× it reads 2.2 microns per division. Write the value on the microscope for each objective and the reticle becomes a permanent ruler.
Objective (100-division reticle)
- Field diameter
- Microns per reticle division
Stage micrometer: 1 mm ÷ 100 divisions = 10 µm per division. Reticle value = field diameter ÷ 100 divisions: 55.0 µm at 4×, 22.0 µm at 10×, 5.5 µm at 40×, 2.2 µm at 100×.
When the field is not what the formula says
A widefield eyepiece changes the answer, and a camera crops it. Field number 26 at 40× gives 0.65 mm, not 0.55 mm; field number 18 at 40× gives only 0.45 mm. Two microscopes with the same 40× objective show different fields if their eyepieces differ — always read the number off the eyepiece you are actually using.
A camera on the microscope sees less than the eye does, because the sensor is smaller than the eyepiece field. The formula gives the visual field through the eyepiece; the camera field is the sensor width divided by the total magnification. The numbers here are estimates from the maker's nominal field number — the Terms of Use state the limits.
- Field diameter
- Field diameter in microns
- Total magnification
- Field diameter
- Field diameter in microns
- Total magnification
Same 40× objective, 400× total: the eye sees 0.55 mm, but a full-frame camera (36 mm sensor ÷ 400×) sees only 0.09 mm.
Practice
Field number 20, 20× objective — A microscope has a field number of 20 and a 20× objective with a 10× eyepiece. Find the field diameter, the total magnification, and the field area.
<strong>Answer:</strong> Diameter = 20 / 20 = 1.0 mm. Total magnification = 20 × 10 = 200×. Area = π × 0.5² = 0.79 mm².
Widefield 26, 60× objective — A super-widefield eyepiece (field number 26) is used with a 60× objective and a 10× eyepiece. Find the field diameter in millimetres and microns, and the total magnification.
<strong>Answer:</strong> Diameter = 26 / 60 = 0.43 mm = 433 microns. Total magnification = 60 × 10 = 600×.
How many paramecia fit across the 40× field? — A paramecium is about 200 microns long. How many fit across a field number 22, 40× field, and what fraction of the field does one fill?
<strong>Answer:</strong> Field = 22 / 40 = 0.55 mm = 550 microns. Count = 550 / 200 = 2.75, so 2 whole paramecia fit across, and one fills 200 / 550 = 0.36 — about a third of the field.
Tap a question to see its answer.
All calculators
- Focal lengthf = D · d / W
- DistanceD = W · f / d
- Crop factorCF = 43.27 / diagonal
- CompareAOV = 2 · arctan(d / (2f))
- CCTVD = (f · px) / (PPM · sensor width)
- TelescopeTFOV = AFOV / M
- BinocularsExit pupil = D / M
- Gaming FOVH = 2 · arctan(tan(V / 2) × aspect ratio)
- TV distanceDistance = width / (2 · tan(θ / 2))
- From a photoW = D · d / f
- Projector throwThrow distance = throw ratio × screen width
- MicroscopeField diameter = FN / objective magnification
No calculator matches your search.
Frequently asked questions
0.55 mm (550 microns) with a field number of 22. The arithmetic is 22 / 40 = 0.55 mm. With a field number of 20 the same objective shows 0.50 mm, and with a widefield 26 it shows 0.65 mm — the eyepiece matters as much as the objective.
No — the field diameter depends on the field number and the objective only. A 40× objective with a 10× eyepiece gives 400× total and a 0.55 mm field; with a 15× eyepiece the total is 600× and the field is still 0.55 mm. The stronger eyepiece magnifies the same circle, it does not widen it.
0.22 mm (220 microns) with a field number of 22. The arithmetic is 22 / 100 = 0.22 mm, and the field area is π × 0.11² = 0.038 mm². A red blood cell at 7.5 microns fits about 29 times across that field.
The eyepiece passes an intermediate image 22 mm across. Field number is that diameter in millimetres, printed on the eyepiece as 10×/22. A bigger field number means a wider view: 26 shows more than 22, and 18 shows less, through the same objective.
Compare it with the field diameter, or read it off a calibrated reticle. A cell spanning half of a 0.55 mm field is about 275 microns wide. For a finer reading, calibrate an eyepiece reticle against a stage micrometer: with 100 reticle divisions across a 0.55 mm field, each division is 5.5 microns.