Skip to content
fieldofviewcalculator.com

CCTV Field of View Calculator

CCTV field of view calculator

Resolution preset
Sensor

Result

Horizontal angle
79.05°
Vertical angle
57.62°
Frame width
33.00 m
Frame height
22.00 m
Pixel density
116.4 px/m
DORI rating at this distance
Observe
Identify distance (250 px/m)
9.31 m
Recognise distance (125 px/m)
18.62 m
Observe distance (62.5 px/m)
37.24 m
Detect distance (25 px/m)
93.09 m
Blind spot
3.13 m
Nearest common CCTV lens
8 mm

Calculate CCTV field of view, pixel density and DORI distances for any camera. Find the lens that detects, observes, recognises or identifies a person.

What does this camera actually cover?

An 8 mm lens on a 1-inch sensor covers 33.00 m wide at 20.0 m, at a horizontal angle of 79.05 degrees. The arithmetic is 20.0 x 13.2 / 8 = 264 / 8 = 33.00 m, and the angle is 2 x arctan(13.2 / 16) = 2 x 39.523 = 79.05 degrees. That is a car park view, not a doorway view, and the width alone tells you which one it is.

Coverage is the first question, and it comes before resolution. A camera that covers the whole car park cannot also read a number plate at the far end. Decide the width first, then check whether the pixels inside that width are enough.

  • Frame width–
  • Horizontal angle–
  • Pixel density at 3840 px–

8 mm lens on a 1-inch sensor. At 5.0 m the frame is 8.25 m wide; at 50.0 m it is 82.50 m wide.

Pixel density decides what you can see

Pixel density is horizontal pixels divided by frame width, and it decides the DORI rating. An 8 mm lens with 3840 px at 20.0 m gives 116.4 px/m, because 3840 / 33.00 = 116.36 px/m, shown as 116.4 px/m. That sits below Recognise at 125 px/m, so the rating at 20.0 m is Observe.

More pixels or a longer lens both raise the density, and a wider frame lowers it. The three levers are resolution, focal length, and distance, and the calculator shows which one you must move. Guessing from the lens alone ignores two of the three.

  • Pixel density–
  • Frame width at 20.0 m–
  • Detect — 25 px/m
  • Observe — 62.5 px/m
  • Recognise — 125 px/m
  • Identify — 250 px/m

Fixed 20.0 m, 8 mm lens, 1-inch sensor. At 1920 px the density is 58.2 px/m (Detect); at 3840 px it is 116.4 px/m (Observe).

The four DORI distances

One camera has four DORI distances, one for each level, and they halve and double in a fixed pattern. An 8 mm lens with 3840 px on a 1-inch sensor gives Identify at 9.31 m, Recognise at 18.62 m, Observe at 37.24 m, and Detect at 93.09 m. The arithmetic for Identify is (8 x 3840) / (250 x 13.2) = 30,720 / 3,300 = 9.31 m, and for Observe it is 30,720 / (62.5 x 13.2) = 30,720 / 825 = 37.24 m.

Read the distances as a map, not a single number. A face 10.0 m away is just past Identify and inside Recognise, so you can tell who it is only if they step 0.69 m closer. The map tells you where to mount the camera, not just which lens to buy.

Tap a DORI level

  • DORI distance–
  • Threshold–
  • Frame width at that distance–

8 mm lens, 3840 px, 1-inch sensor. A face 10.0 m away is just past Identify (9.31 m) and inside Recognise (18.62 m).

Finding the right CCTV lens

The lens you need comes from the width you must fit: f = D x d / W. To fit a 6.0 m wide entrance at 10.0 m on a 1-inch sensor you need 22.0 mm, because 10.0 x 13.2 / 6.0 = 132 / 6.0 = 22.0 mm. The nearest common CCTV lens is 25 mm, which gives a 5.28 m frame at 10.0 m and a 29.58 degree horizontal angle.

A varifocal lens covers the gap when the exact number falls between fixed lenses. A 2.8 to 12 mm varifocal covers entrances and rooms, and a 12 to 50 mm varifocal covers perimeters and gates. Buy the range that contains your calculated number, not the longest lens on the shelf.

Tap a CCTV lens

  • Frame width at 10.0 m–
  • Horizontal angle–
  • Lens needed for a 6.0 m entrance–
  • Frame vs 6.0 m target–

Target: a 6.0 m wide entrance at 10.0 m on a 1-inch sensor needs 22.0 mm; the nearest common lens is 25 mm, giving a 5.28 m frame.

The blind spot under the camera

The ground right under a camera is blind, and the blind distance comes from height, tilt, and vertical angle. A camera at 3.0 m height, tilted 15 degrees down, with an 8 mm lens on a 1-inch sensor has a vertical angle of 57.62 degrees, so its lower edge points 43.81 degrees below horizontal, and the blind distance is 3.0 / tan(43.81 degrees) = 3.0 / 0.959 = 3.13 m. Anyone standing closer than 3.13 m is under the frame.

Mounting higher widens the blind spot, and tilting down narrows it. A camera mounted at 6.0 m with the same tilt has a blind distance of 6.25 m, which is a whole doorway of unseen ground. Check the blind spot before you mount, not after a break-in.

  • Blind distance–
  • Lower edge of frame–

8 mm lens on a 1-inch sensor, tilted 15° down; vertical angle 57.62°. At 3.0 m the blind spot is 3.13 m; at 6.0 m it is 6.25 m.

  • Blind distance–
  • Lower edge of frame–

Camera at 3.0 m height. No tilt: blind spot 5.45 m; tilted 45° down: 0.87 m.

Entrance, car park, and perimeter

Three scenes need three lenses, and one lens cannot serve all three. An entrance 3.0 m wide at 8.0 m needs 35.2 mm, because 8.0 x 13.2 / 3.0 = 105.6 / 3.0 = 35.2 mm. A car park 33.0 m wide at 20.0 m needs 8.0 mm, because 20.0 x 13.2 / 33.0 = 264 / 33.0 = 8.0 mm. A perimeter 16.5 m wide at 30.0 m needs 24.0 mm, because 30.0 x 13.2 / 16.5 = 396 / 16.5 = 24.0 mm.

Plan one camera per job. The entrance camera identifies faces, the car park camera observes movement, and the perimeter camera detects approach. A single wide camera over the entrance gives Detect at best, and a face at 20.0 m is a blur of 116.4 px/m at Observe, not an identification.

Pick a scene

  • Lens needed–
  • Pixel density–
  • Identify distance with that lens–

1-inch sensor, 3840 px. Entrance 3.0 m at 8.0 m needs 35.2 mm; car park 33.0 m at 20.0 m needs 8.0 mm; perimeter 16.5 m at 30.0 m needs 24.0 mm.

Resolution is not a cure for the wrong lens

Doubling the resolution doubles the pixel density, but it cannot fix a frame that is ten times too wide. A 4 mm lens with 1920 px at 10.0 m gives 58.2 px/m, because the frame is 33.00 m wide and 1920 / 33.00 = 58.18 px/m, shown as 58.2 px/m. That is below Observe at 62.5 px/m, so even a jump to 3840 px only reaches 116.4 px/m, still below Recognise.

Spend the money on the lens first and the resolution second. A 16 mm lens with 3840 px at 30.0 m gives 155.2 px/m, because the frame is 24.75 m wide and 3840 / 24.75 = 155.15 px/m. That is Recognise, and it comes from the narrower frame, not from the pixel count alone.

  • Frame width–
  • Pixel density–
  • Frame width–
  • Pixel density–

Starting point: 4 mm lens, 1920 px at 10.0 m — 33.00 m frame, 58.2 px/m (Detect). Both upgrades double the density to 116.4 px/m, but only the longer lens narrows the frame to 16.50 m.

When DORI does not apply

DORI assumes a flat, well-lit target facing the camera, and real scenes break that assumption. A face turned away, a plate at a sharp angle, rain on the lens, or a scene lit only by a doorway bulb all lower the usable detail below the px/m number. The DORI distance is a planning figure, not a guarantee written in court.

Use the numbers to place cameras, then test them with a real person walking the route. If the test face is unreadable at the calculated Identify distance, move the camera closer or fit a longer lens. The standard gives you the plan, and the walk-through gives you the proof.

  • Pixel density–
  • Frame width–
  • Identify — 250 px/m
  • Recognise — 125 px/m
  • Observe — 62.5 px/m
  • Detect — 25 px/m

8 mm lens, 3840 px, 1-inch sensor. Boundaries: Identify 9.31 m, Recognise 18.62 m, Observe 37.24 m, Detect 93.09 m.

Practice

  • Find the DORI distances for a 16 mm lens with 3840 px on a 1-inch sensor.

    <strong>Answer:</strong> Identify (16 x 3840) / (250 x 13.2) = 61,440 / 3,300 = 18.62 m; Recognise 37.24 m; Observe 74.47 m; Detect 186.18 m.

  • Find the lens for a 3.0 m doorway at 8.0 m on a 1-inch sensor.

    <strong>Answer:</strong> f = 8.0 x 13.2 / 3.0 = 105.6 / 3.0 = 35.2 mm. Nearest common lens: 25 mm is too wide (4.22 m frame) and 50 mm is too tight (2.11 m frame), so use a varifocal covering 35 mm.

  • Find the pixel density of a 12 mm lens with 2560 px at 20.0 m on a 1-inch sensor.

    <strong>Answer:</strong> W = 20.0 x 13.2 / 12 = 264 / 12 = 22.00 m; PPM = 2560 / 22.00 = 116.4 px/m, which is Observe, just below Recognise at 125 px/m.

Tap a question to see its answer.

All calculators

Frequently asked questions

You need 22.0 mm, so fit a 25 mm lens. The arithmetic is 10.0 x 13.2 / 6.0 = 132 / 6.0 = 22.0 mm on a 1-inch sensor. A 25 mm lens gives a 5.28 m frame at 10.0 m, because 10.0 x 13.2 / 25 = 132 / 25 = 5.28 m, and a 29.58 degree horizontal angle, because 2 x arctan(13.2 / 50) = 2 x 14.79 = 29.58 degrees. The 22.0 mm exact value gives 33.40 degrees.